Microsoft EA900 Guide d'installation

EA900 ADSL USB Modem Installation Guide Microsoft® Windows® 98, 98SE, 2000, Me and XP Driver Version V5.4.1-1120 / Rev 1.00 For Annex A & Ann

72. Insert the Drivers CD into the CD-ROM drive and double click Setup.exe to start the installation procedure. A notification message will appear

8[For Windows 98/98SE only] 8-1. Insert Drivers CD-ROM disc into CD-ROM drive and then click on OK. 8-2. To specify the directory of Windows 98/98SE

9 Chapter 3: ADSL Control and Status ACCESSING CSA The User Interface to the ADSL Modem is provided by the Control and Status Application (CSA

10CSA USER SCREEN Modem Performance The Modem Performance displays performance information. The primary purpose is to display the instantaneous t

11• ADSL Modem not available Connect/ Disconnect Button The CONNECT/DISCONNECT button performs the connection/disconnection operation. If the ADS

12 Chapter 4: Uninstall Software Remove the ADSL Modem drivers by performing the following steps. Note: The USB cable should not be unplugged

13 Appendix A: Modifying TCP/IP Networking Options RFC 1483 Mode Microsoft Windows 98, First and Second Editions TCP/IP settings are automati

144. The “Gateway” tab allows you to add or remove gateways. Consult with your network administrator to determine the appropriate addresses for you

15Microsoft Windows Me TCP/IP settings are automatically set up during the software installation process. The following procedure may be used to c

164. The “Gateway” tab allows you to add or remove gateways. Consult with your network administrator to determine the appropriate addresses for you

Specification subject to change without notice. Alcatel is a trademark of Alcatel Microelectronics, All other products or services mentioned are the

17Microsoft Windows 2000 TCP/IP settings are automatically set up during the software installation process. The following procedure may be used to

184. The “Internet Protocol (TCP/IP) Properties” window is used to modify the IP addresses and DNS Server addresses: $ Change the IP address to a

19Microsoft Windows XP TCP/IP settings are automatically set up during the software installation process. The following procedure may be used to c

204. The Internet Protocol (TCP/IP) Properties window is used to modify the IP addresses and DNS Server addresses: $ Change the IP address to a use

21 RFC 2364 / RFC 2516 Mode Microsoft Windows 98, First and Second Editions TCP/IP settings are automatically set up during the software installat

225. The “TCP/IP Settings” window is used to modify the IP address, Name Server addresses and/or default gateway as follows: $ Change the IP addr

23 Microsoft Windows Me TCP/IP settings are automatically set up during the software installation process. The following procedure may be used to

244. The “TCP/IP Settings” window is used to modify the IP address, Name Server addresses and/or default gateway as follows: • Change the IP addr

25Microsoft Windows 2000 TCP/IP settings are automatically set up during the software installation process. The following procedure may be used to

265. From the “Networking” tab of the “My ADSL ISP Properties” window, select Internet Protocol (TCP/IP) and click Properties. 6. The “Internet P

TABLE OF CONTENTS About This Manual ...1 Preface..

27Microsoft Windows XP TCP/IP settings are automatically set up during the software installation process. The following procedure may be used to c

285. From the “Networking” tab of the “My ADSL ISP Properties” window, select Internet Protocol (TCP/IP) and click Properties. 6. The “Internet P

29 Appendix B: Connector Pin-out The ADSL modem is equipped with a RJ-11 jack for connection to the ADSL data port. The center two pins, pins

30 Appendix C: Troubleshooting If your internet connection is not working, the following hints may be helpful. After trying these hints, if y

31 Appendix D: Abbreviations AAL ATM Adaptation Layer. A function performed during ATM cell processing to adapt traditional IP or Ethernet

32VCI Virtual Circuit Identifier. A 16-bit value that is included in an ATM cell header to identify the destination virtual circuit. VPI Virtual

33 Appendix E: Government compliance notices FCC compliance This equipment complies with Part 68 of the FCC Rules. On this equipment is a lab

34DOC compliance information NOTICE: The Canadian Department of Communications label identifies certified equipment. This certification means that t

1 About This Manual This manual provides a comprehensive user’s guide and installation manual for ADSL USB modems. It has been organized in such

2 Preface The ADSL USB Modem Manual This manual contains information regarding the installation, operation, and configuration of the ADSL USB Mo

3 Chapter 1: Overview About ADSL Asymmetric Digital Subscriber Line (ADSL) technology provides high-speed data access across regular phone lines

4Features The ADSL USB Modem provides the following features: • Compliant with Universal Serial Bus Specification Revision 1.1 • USB bus-powered;

5 Chapter 2: ADSL USB Modem Installation and Software Setup Be sure to follow the instructions provided for your PC’s operating system. The fol

6Modem Installation 1. Insert the rectangular end of the USB cable into the USB port of your PC. 2. Insert the square end of the USB cable into